ABOUT US

A：The punch material can be customized according to client requirement for tablet press machine, but the charges will be increased for sure.

A：Normally we divide tablet press machine into different series, ZP-Series, ZPT-Series, GZP-Series and non-standard FZP-Series.

ZP-Series is our standard tablet press machine which can do Max. 25mm diameter.

ZPT-Series is our improved type tablet press machine which comes with automatic lubrication system and all features the same to high speed tablet press machine, just with slower rotation speed than high speed tablet press machine.

GZP-Series is our high speed tablet press machine which can do Max. 110rpm/min with Max. 25mm diameter.

FZP-Series is our non-standard tablet press machine which can be customized according to client requirement, especially when you have bigger tablet size which exceed our 25mm diameter.

A：European standard: IPT

D-type punch refers to the diameter of the punch rod: 25.35mm, the middle mold: 38.1mm,

B-type punch refers to the punch diameter: 19mm, the middle mold: 30.16mm,

BB type punch refers to the punch diameter: 19mm, the middle mold: 24mm,

Therefore, after confirming the die type, the tablet diameter is determined.

In other words, after confirming the maximum sheet diameter, the type of die can be confirmed.

A：Change as much as you want within the size range.

A：The pattern should not be too complicated, without sharp corners, because the more corners, the more difficult it is to process. Then the angular tool can’t get in and can’t process it.

A：It is not easy to calculate. Usually, the mold must be disassembled and the turntable must be cleaned after each batch. If you are using corrosive material for tablet press,we will use different material for the punch and for the turret. So before you order tablet press machine, you’d better to tell us what material you are going to press.

A：It can be disassembled, and the turntable can be replaced by a high-speed machine as a whole.

A：The standard is 6mm. Increasing the thickness will increase the extra cost. If it is more than 12mm, add 2,000USD. The extra cost of no more than 12mm will not increase much.

A：Yes, the tablet press machine can do this function.

A：Determined according to the specific model. The standard European standard type D is 25 mm in diameter. If there are special requirements, we need to customize for you.

A：Material fluidity, feeder form, material composition, pressure, ambient temperature and humidity, all above conditions are very critical for tablet press machine.

A：Yes, the better the fluidity of the material, the better the uniformity, depending on the material, it is usually about 0.1 mm.

A：The hydraulic tablet press is relatively easy to adjust the pressure, but there is a risk of oil leakage. Now our GZP-Series and ZPT-Series can equip with automatic pressure adjustment system without hydraulic system.

A：ZPS is a European standard D-type punch with pre-pressure, main pressure and pressure sensing system. Standard touch screen control.

A：Pre-compression is mainly used to remove powder and air to prevent uneven tablet weight. After the powder is pre-pressed, it reaches the main pressure. After the main pressure, the tablet reaches the target tablet weight and hardness. The size of the main pressure can be controlled through the touch screen. The main difference between pre-compression and double-pressure single-out is that there is only one feeding port for pre-compression, and two for double-pressure single-out.

A：GZP-Series High-speed Tablet press machines are equipped with pre-compression, sub-high-speed machine ZP-540, low-speed machine ZP-420 double pressure single output.

A：Ordinary ZP can do it, but at least two feeding hoppers are needed to make double layers, We also call it Bi-Layer Tablet Press Machine.

A：Yes, it can be adjusted manually within the effective filling range of the equipment.

A：Single Punch Tablet press machine production capacity calculation, Type 1.5: 4500 tablets/hour. Type 5: 4000 pieces/hour. Type 6: 2500 tablets/hour.

A：Single punch tablet press machine Need lubrication and cleaning process after each production batch.

A：This depends on the size and output. For a single-punch tablet machine, only the high-pressure model TDP-6 can be recommended.

A：The material is made into particles with less powder to solve this problem. The equipment itself cannot solve this problem, or add a sieving machine at the back.

A：Usually a SP-Series or GSP-Series Tablet De-dust machine is needed.

A：The dust collector, also called the powder remover, is used to remove and collect the excess powder that falls outside when the powder is pressed. Single-color tablet press machine requires 1 dust collector, 2-color tablet press machine requires 2 dust collectors, and 3-color tablet press machine requires 3 dust collectors.

A：Centralized lubrication system: This requires an oil pump, which needs to be manually pressed before each batch production.

Automatic circulation lubrication system: After this equipment is turned on, it will automatically circulate lubrication.

The automatic circulation lubricating system is a fully enclosed system, with less oil loss in the circulation, and the production will not leak oil.

A：ZP mold punch cannot be used, and the punch height of the die is not enough. But this lubrication system Can be equipped with ZPT and IPT molds.

A：The color can be changed, and yellow is a warning color.

A：Because the material is too sticky, some powder will remain in the die during the tableting process, and the surface of the tablet will not be smooth. At this time, an additional powder blowing machine must be equipped for tablet better output.

A：Normally the client requires to change the granulation formulation or use a powder blowing machine for better tablet output.

A：It is mainly used to detect metal residues in materials, because some machines may produce rust during production, and iron filings are mixed in the materials, so a metal detector machine is required. GMP regulations require the detection of metal residues.

A：First adjust the pre-pressure, main pressure and rotation speed, etc. of the tablet press machine, and then if it fails, you can only look for the particles, such as the particles are too dry, the moisture is too small, the adhesive viscosity is not enough, and so on.

A：This is generally because the fluidity of the particles is not very good, or it may be that the passage of the feeder is blocked, resulting in uneven feeding.

A：Usually large-volume tablet presses need to use a feeder. For models above ZP-31D, the price of a feeder is 3,000USD.

A：Vacuum feeder is an automatic feeding device installed on the tablet press machine. Single-color tableting requires 1 vacuum feeder, 2-color tableting requires 2 vacuum feeders, and 3-color tableting requires 3 Vacuum feeder.

A：Relying on the self-fluidity of the material to fill the middle die cavity for tablet compression, the fluidity of the material is required to be good.

A：Usually, the closed type is used for high-speed tablet press machine, and the open type is used for low-speed tablet press machine.

A：The fluidity is poor, the diameter of the tablet is large, and the tablet press machine speed is fast.

A：There is a rotating scraper in the forced feeder to help the material be filled into the middle die, which is suitable for materials with poor fluidity and can also make the material filling more uniform.

A：Pharmaceutical factories have higher requirements for weight, so high-speed tablet pressing machines are equipped with automatic sampling and automatic pressure detection systems.

A：Depending on the viscosity of the material, magnesium stearate is generally added, the surface will be smoother, but the finished product will dissolve slowly in water.

A：According to the characteristics of the material, control the temperature (17°C) and humidity (17%), produce for 2-3 hours, and clean up once.

A：Two solutions: blowing magnesium stearate on the mold, and the lower mold automatically rotates when the material is discharged to prevent sticking.

A：The stroke of the moving pressure roller.

A：Turntable, feed hopper, discharge port.

A：No, only high-speed tablet presses have this function.

A：Depending on the specific material, the low speed is 25rpm, the sub-high speed is 35-45rpm, and the high speed is 80-120rpm.

A：Available, English version.

A：There are requirements for hardness, and pharmaceuticals factories have the most stringent requirements, and hardness testers are usually used for sampling and testing.

A：National regulations do not exceed 1%.

A：30*20mm(50g), 30*16mm(25g), 25mm diameter*8mm(15g).